[GBW] Question about a Tool
wminter at pennswoods.net
Tue Dec 10 20:33:02 EST 2013
The tool that you describe with the connector pins at the end of the
handle is identical to the typeholder that Frank Mowery received from
Another bit of trivia about heating tools for gold tooling: Peter
Waters and Roger Powell (English binders and book conservators) also
realized the benefit of electrically heating a holder for their
decorative tools. They used a soldering iron and modified all of
their type and decorative tools --- more information about this is
planned for an article in the GBW NEWSLETTER.
All the Best,
William Minter Bookbinding & Conservation, Inc.
4368 Woodbury Pike
Woodbury, PA 16695
Email: wminter at pennswoods.net
On Dec 10, 2013, at 9:03 AM, Peter Geraty wrote:
> I don’t know how useful this is but after Fritz Eberhardt dies I
> bought his set of electric tools from Trudi. I was always
> fascinated that he could shape brass and place it in the various
> handles he had to tool the unusual shapes he made. There is a tool
> for single letters of type, one for line and decorative pallets and
> one, a standard lettering pallet much like the ones you have. The
> tools were made by L Berens in Hamburg and have a transformer that
> three tools can be plugged into at a time. The element is in the
> same location as the one you have but the cord feeds from the end
> of the handle, a more convenient location for using. I wonder if
> there is a way to move your cord.
> The set up is perfect for a small shop such as the one Fritz and
> Trudi maintained. They didn’t need pallets, center tools or corners
> with handles, they only needed the brass tools themselves. I
> suspect, however that these tools might have been made for
> production tooling as you could keep your type or pallets on a
> stove and merely keep switching them out of a constantly heated
> tool thereby loosing very little time in heating. After all it is
> the heating of the massive pallet which takes time, not the tiny
> type so being able to keep the tool at a constant heat is very useful.
> I admit I don’t use his tools very often but we do have a heated
> tool we use in the shop regularly. It is a roll we bought from Fort
> Hill Engraving many years ago, they still make them for the
> furniture industry to tool gold foil on tabletops. We had one at
> Harcourt Bindery which was where I was introduced to it. It is
> great for tooling gold lines around leather labels or tooling lines
> on the covers of half leather bindings. Fort Hill sells rolls to go
> on it but don’t get them they are very poorly made, or at least
> they were years ago. We have P & S send us rolls with no handle and
> the hole for the arbor is drilled out to ½” so it will fit the
> heated roll. In the end it is cheaper to go this way and it is very
> nice to have the roll at a constant temperature.
> Peter Geraty
> Praxis Bindery
> 1 Cottage Street, Room 4-24
> Easthampton, MA 01027-1667
> pgeraty at praxisbindery.com
> On Dec 8, 2013, at 4:38 PM, Joanne Berkowitz <joannebe at pacbell.net>
>> I'd appreciate posting this to the list:
>> I bought the contents of a small bindery and this electric type
>> holder was in it. The cord was very frayed and damaged and it had
>> been repaired before and again now and it actually works. Has
>> anyone any experience with these? Are they useful? Is there a
>> place to get parts as I have two but the second is not complete.
>> Does anyone know when this may have actually been used? It had a
>> very old fashioned 2-wire cord and someone had wired a primitive
>> thermostat into the cord at an earlier date. Comments below are
>> from my brother who repaired it.
>> Thanks for any info.
>> Joanne Berkowitz
>> Sacramento, CA
>> Fixed the tools as best I could.
>> Tool on Left:
>> Guy apparently tried to replace the heater but couldn't find the
>> exact replacement so he kludged in a different heater. That's why
>> the heater cover is all bent up with screws put in different places.
>> I fixed the wiring from the heater to the switch so it is a little
>> He put a 3 wire power cord on. Since the device was made before 3
>> wire cords even existed, the ground wire was doing absolutely
>> nothing. I replaced the power cord with a two wire cord.
>> One of the thumbscrews was not held in place with anything so it
>> turned freely. The other thumbscrew was held on by a bent nail.
>> I installed cotter pins for both thumbscrews.
>> I tested the thing. It heats up, the switch works correctly and
>> it is relatively safe but there is no guarantee on how long it
>> will last.
>> Tool on Right:
>> Looks like it's supposed to have the same heater as the other
>> tool. Since these things are antiques, it is probably hard or
>> impossible to get the right heater. Do you know of anywhere you
>> can get heaters of any sort for these things?
>> Removed and replaced the broken screw for the handle.
>> The wooden handle turns rather freely. Should I find some way to
>> stop it from turning?
>> GBW: The NEW email list for GBW member communications
>> For info about the list or to change your settings, visit http://
>> GBW Calendar of Events Online
>> Horizons - GBW 2012-2014 Traveling Exhibition
>> To post messages, email to GBW at list.guildofbookworkers.org
>> For problems, contact Henry Hebert, List Manager:
>> communications at guildofbookworkers.org
> GBW: The NEW email list for GBW member communications
> For info about the list or to change your settings, visit http://
> GBW Calendar of Events Online
> Horizons - GBW 2012-2014 Traveling Exhibition
> To post messages, email to GBW at list.guildofbookworkers.org
> For problems, contact Henry Hebert, List Manager:
> communications at guildofbookworkers.org
-------------- next part --------------
An HTML attachment was scrubbed...
More information about the GBW